GB/T 22199.2-2017 in English

《GB/T 22199.2-2017电动助力车用阀控式铅酸蓄电池 第2部分：产品品种和规格》由TC69（全国铅酸蓄电池标准化技术委员会）归口，主管部门为中国电器工业协会。

ChinaStandards.net is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.

GB/T 22199 Valve-regulated Lead-acid Batteries for Moped consists of the following two parts under the general title:

——Part 1: Technical Conditions;

——Part 2: Kinds of Products and Specifications.

This is Part 2 of GB/T 22199.

This part is developed in accordance with the rules given in GB/T 1.1-2009.

This part was proposed by China Electrical Equipment Industrial Association.

This standard is under the jurisdiction of the National Technical Committee on Lead-acid Batteries of Standardization Administration of China (SAC/TC 69).


Valve-regulated Lead-acid Batteries for Moped - Part 2: Kinds of Products and Specifications

1 Scope

This part of GB/T 22199 specifies the model preparation, kinds, overall structures and specifications of the valve-regulated lead-acid batteries for moped.

This part is applicable to valve-regulated lead-acid batteries (hereinafter referred to as batteries) and battery packs with capacity of 28Ah and below for electric bicycles, electric scooters, electric balance vehicles, electric wheelchairs, etc., which are mainly powered by batteries. The sulfuric acid electrolyte in a battery is non-liquid, but adsorbed to the microporous structure between electrodes or in the form of a colloid.

This part is not applicable to lead-acid batteries and battery packs for other purposes such as starting, electric road vehicles and traction.

2 Normative References

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

JB/T 2599 Drawing-up and Designation Method of Name and Model of Lead-acid Battery

3 Model Preparation

The battery product model shall meet the requirements of JB/T 2599, specifically, the product type is represented by the initials “DZ” of the Chinese phonetic letters “Diandong Zhuli”. The detailed naming diagram is shown in Figure 1.

Example:

Figure 1 Model Naming Diagram

4 Kinds of Batteries

Name: valve-regulated lead-acid battery

5 Overall Structures and Specifications of Batteries

5.1 Specifications and dimensions of batteries

See Table 1 for specifications and dimensions of batteries.

Table 1 Specifications and Dimensions of Products
S.N. Specification Rated voltage
V Rated capacity
Ah Boundary dimension
mm
Length (l) Width (b) Height (H) Total height (Hmax)
1 6-DZF-7 12 7 151±2 65± 94±2 103
2 6-DZF-12 12 12 151±1 99±1 98±1 105
3 6-DZF-14 12 14 152±2 99±2 107±2 115
4 6-DZF-20(A) 12 20 181±2 77±2 170±2 175
5 6-DZF-20(B) 12 20 161±2 110± 121±2 123
6 6-DZF-20(C) 12 20 200±2 98±2 121±2 123
7 6-DZF-22 12 22 185±1 105±1 135±1 137
8 6-DZF-28 12 28 165±2 125±1 175±2 179

5.2 Overall structure of batteries

See Figure 2 for the overall structure of batteries.


Figure 2 Dimensions of Overall Structure

5.3 Overall dimensions of a battery terminal

5.3.1 See Figure 3 for the diagram for Z-shaped terminal.

The dimensions given in Figure 3 are in millimeters (mm), with a given dimensional tolerance of ±10%.

Note: special terminals may be determined through negotiation between the supplier and the purchaser.


Figure 3 Diagram for Z-shaped Terminal

5.3.2 See Figure 4 for the diagram for L-shaped terminal.

The dimensions given in Figure 4 are in millimeters (mm), with a given dimensional tolerance of ±10%.

Note: special terminals may be determined through negotiation between the supplier and the purchaser.

Foreword i
1 Scope
2 Normative References
3 Model Preparation
4 Kinds of Batteries
5 Overall Structures and Specifications of Batteries