GB/T 39600-2021 in English

《GB/T 39600-2021人造板及其制品甲醛释放量分级》由TC198（全国人造板标准化技术委员会）归口，主管部门为国家林业和草原局。

ChinaStandards.net is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.

This standard is developed in accordance with the rules given in GB/T 1.1-2009.

This standard was proposed by the State Forestry Administration of the People's Republic of China.

This standard is under the jurisdiction of the National Technical Committee on Wood-based Panels of Standardization Administration of China (SAC/TC 198).


Formaldehyde emission grading for wood-based panel and finishing products

1 Scope

This standard specifies the requirements, test methods and judgment rules of formaldehyde emission grading.

This standard is applicable to the formaldehyde emission grading for various interior wood-based panel and finishing products, such as fiberboards, particleboards, plywoods, blockboards, reconstituted decorative woods, laminated veneer lumbers, laminated woods, decorated wood-based panels, wood-based floorings, wood-based wall-boards and wood-based doors.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.

GB/T 17657-2013 Test methods of evaluating the properties of wood-based panels and surface decorated wood-based panels
GB/T 18259-2018 Terminology for wood-based panels and their surface decoration
GB 18580-2017 Indoor decorating and refurbishing materials - Limit of formaldehyde emission of wood-based panels and finishing products

3 Terms and definitions

For the purposes of this document, the terms and definitions given in GB/T 18259-2018 apply.

4 Requirements

The formaldehyde emission of interior wood-based panel and finishing products is classified into three grades according to the emission limit, as shown in Table 1.

 
Table 1 Formaldehyde emission grading for interior wood-based panel and finishing products
In mg/m3
Formaldehyde emission limit grade Limit Identification
Grade E1a ≤0.124 E1
Grade E0 ≤0.050 E0
Grade ENF ≤0.025 ENF
a The formaldehyde emission limit and identification for Grade E1 are those for wood-based panel and finishing products specified in GB 18580-2017.

5 Test methods

5.1 Preparation of test piece

5.1.1 For wood-based panel and finishing products with both sides exposed for use, the test piece has a length of l=(500±5)mm and a width of b=(500±5)mm, and two test pieces are prepared with edge sealed with formaldehyde-free aluminum tape. The length of each test piece with edge unsealed is (750±5)mm.

5.1.2 For wood-based panel and finishing products with only one side exposed for use, such as wood-based flooring and wood-based wall-board, only the exposed side is tested, and the test piece has a length of l=(500±5)mm and a width of b=(500±5)mm. If the samples are not enough in size, they may be spliced for preparing the test pieces. Four test pieces are prepared before sticking two test pieces back to back with formaldehyde-free adhesive or sealing the back and all sides of the test piece with formaldehyde-free aluminum tape.

5.1.3 For hollow particleboards, the test piece has a length of l=(500±5)mm and a width of b=(500±5)mm, and two test pieces are prepared with porous edge sealed with formaldehyde-free aluminum tape. The length of exposed imperforate edge is (750±5)mm.

5.1.4 For the laminated woods, two test pieces are prepared with edge unsealed. The total exposed area equals to the total surface area, and the total area of each piece is 0.50m2. If the samples are not enough in size, they may be spliced for preparing the test pieces.

5.1.5 For the wood-based doors, two test pieces are prepared by reserving two side frames and the bottom frame, and each piece has an exposed area (excluding the four sides) of 0.50m2, with sawing edges sealed with formaldehyde-free aluminum tape.

5.2 Determination of formaldehyde emission

The formaldehyde emission is determined according to those specified in GB/T 17657-2013, 4.60, and the result is accurate to 0.001mg/m3.

6 Judgment rules

If the inspection result complies with the specified limit for a grade, the test piece shall be judged as meeting the requirements of the grade.

Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test methods
6 Judgment rules