SY/T 6117-2016 in English
VALIDThe operating and maintenance of petroleum drilling rig and workover rig
- Issued on:2016-12-05
- Implemented on:2017-05-01
- File Format:PDF
- Delivery:Via email within 5 business days
$408.00
本标准规定了石油钻机和修井机在作业现场使用与维护的总则、使用要求、维护要求，以及拆装、运输（移运）和贮存要求。本标准适用于GB/T 23505中定义的陆地石油钻机和修井机。
Introduction
Interpretation of the core content of the standard
| Comparison dimensions | 2010 edition | 2016 edition |
|---|---|---|
| Scope of application | Workover rig only | Drilling rig + Workover rig |
| Structural chapters | 5 chapters | 6 chapters + 2 appendices |
| Safety requirements | Basic clauses | Separate normative appendix |
Key technical requirements
Equipment Usage Specifications
The maximum hook load continuous working time during derrick operation shall not exceed 30 seconds, and the response time of the overhead crane anti-collision device shall be ≤1.5 seconds. The working pressure of the hydraulic system shall be maintained within the range of 0.6-1.0MPa.
Maintenance cycle system
- Shift maintenance: Daily lubrication point inspection (including winch brake system)
- Monthly maintenance: Non-destructive testing of key load-bearing parts (derrick welds, traveling block hook, etc.)
- Annual maintenance: Third-party testing and issuance of SY/T 6326 compliance report
Implementation key points analysis
Typical application scenarios
In shale gas development, special attention should be paid to the detection of the gap between the overlapping sections of the hydraulic cylinder telescopic derrick. The standard requires that the gap between the centralizer and the piston rod should comply with the specified value of GB/T 30216.
Safety Management Matrix
| Risk Type | Control Measures |
|---|---|
| Derrick Instability | Guard Rope Preload Detection + Wind Speed>38.6m/s Warning |
| Electrical Explosion-Proof | Regional Levels According to SY/T 10041 |
Standard Evolution Background
The 2016 version integrates the technical requirements of drilling rigs and adds 12 referenced standards (such as SY/T 6870 top drive specification), reflecting the technical development needs of deep and ultra-deep well operation equipment. In particular, the maintenance requirements of digital control systems are strengthened.
Loading PDF document...
Error loading PDF. Please make sure the file is valid and try again.
We also recommend
-
SY/T 5429-1991 in English
Small diameter flow moisture tester
1992-01-15 -
SY 5488-1992 in English
Anti-mill operating procedures set out
1992-09-17 -
SY/T 5358-2010 in English
Formation damage evaluation by flow test
2010-08-27 -
SY/T 5231-2010 in English
Security Management Standard for Computer Information System of Petroleum Industry
2010-05-01 -
SY/T 6554-2019 in English
Safe hot tapping practices in the petroleum
2019-11-04 -
SY/T 0076-2023 in English
Standard for design of natural gas dehydration
2023-05-26 -
SY/T 6662.2-2020 in English
Non-metallic composite pipe for petroleum and natural gas industries- Part 2: Flexible composite pipe for high pressure transmission
2020-10-23 -
SY 4028-1993 in English
Standard for Quality Inspection and Evaluation of Petroleum Construction Engineering the Work for Plant Installation
1993-09-09 -
SY/T 5890-1993 in English
Method for evaluating the performance of fungicides
1994-01-06 -
SY/T 0310-2019 in English
Code for engineering design of instrument control system in beach-shallow sea
2019-11-04
