GB/T 14663-2024 in English
VALIDPlastic package moulds—Technical specifications
- Issued on:2024-09-29
- Implemented on:2025-04-01
- File Format:PDF
- Delivery:Within 1 day
$210.00
| Standard No: | GB/T 14663-2024 |
| Document status: | VALID |
| Title in English: | Plastic package moulds—Technical specifications |
| Title in Chinese: | 塑料封装模 技术规范 |
| Language: | English |
| File Format: | Electronic (PDF) |
| Delivery: | Within 1 day |
| Issued on: | 2024-09-29 |
| Implemented on: | 2025-04-01 |
| Superseding: |
GB/T 14663-2007 Specification of plastic packaging moulds
|
| ICS Classification: | 25.120.30-Moulding equipment |
| Chinese Classification: | J46-Mould |
| Professional Classification: | GB-National Standard |
| Related Keywords: | technical specifications
technical specifications introduction in-depth interpretation plastic package moulds plastic packaging mold technology plastic packaging molds |
| Related Topics: | Plastic
encapsulation Plastic packaging inspection specifications gb/t 14663-1993 |
《GB/T 14663-2024塑料封装模 技术规范》由TC33（全国模具标准化技术委员会）归口，主管部门为国家标准委。
Introduction
In-depth interpretation of GB/T 14663—2024 "Technical Specifications for Plastic Packaging Molds"
1. Background and significance of standard revision
Since its first release in 1993, the GB/T 14663 series of standards has undergone many revisions, fully reflecting the rapid development of plastic packaging mold technology.
- Added a technical requirements chapter, and detailed the structure, safety and performance regulations
- Optimized the test methods and inspection rules
- Added the relative vacuum degree requirements for vacuum molds
- Improved the applicability and operability of the standard
2. Comparative analysis of standard frameworks
| Standard dimensions | GB/T 14663—2007 | GB/T 14663—2024 |
|---|---|---|
| Structural requirements | The number of X and Y direction guide mechanisms for the upper and lower molds is not specified | At least two combined mold guide mechanisms are required |
| Materials and surface treatment | The coating requirements for molding inserts and runner inserts are not specified in detail | New requirements for hard chrome or chromium nitride plating, with thickness ≥0.5μm and ≥1μm respectively |
| Performance test | The test method for vacuum mold is not included | The requirement of relative vacuum degree ≤-0.08MPa is added |
3. Suggestions for the implementation of the standard
Enterprises should focus on the following aspects when implementing this standard:
- Structural design optimization:Strictly set the mold volume deviation in accordance with the requirements of GB/T 14663-2024 to ensure that the cavity size tolerance meets the requirements of Table 3.
- Material selection and surface treatment:Select high wear-resistant materials such as Cr12MoV and Cr12Mo1V1, and perform coating treatment according to standard requirements.
- Test method verification:During the mold trial stage, use customer drawings to detect the size and surface quality of plastic sealed parts according to 5.10.
- Safety and environmental protection:Set safety signs in conspicuous positions of the mold, and ensure that the eyebolts meet the requirements of GB/T 825.
Loading PDF document...
Error loading PDF. Please make sure the file is valid and try again.
We also recommend
-
GB/T 39164-2020 in English
Tools for moulding—Thermal insulating sheets for injection moulds
2020-10-11 -
GB/T 4678.18-2024 in English
Die casting dies—Components—Part 18: Support pillars
2024-09-29 -
GB/T 8844-2017 in English
Diecasting dies--Specifications
2017-09-29 -
GB/T 23562.1-2009 in English
Steel-plate die holders of stamping dies—Part 1:Rear-pillar die holders
2009-04-02 -
GB/T 4678.20-2025 in English
Die casting dies—components—Part 20: Hoisting columns
2025-05-30 -
GB/T 20914.1-2007 in English
Stamping dies—Gas springs—Part 1:General specification
2007-03-12 -
GB/T 30218-2013 in English
Fine blanking dies - Specifications
2013-12-31
