GB/T 27939-2011 in English

VALID

Plain bearings—Quality control techniques and inspection of geometrical and material quality characteristics

Issued on:2011-12-30
Implemented on:2012-10-01
File Format:PDF
Delivery:Via email within 8 business days

Price(USD)： $660.00
$641.00

Standard No:	GB/T 27939-2011
Document status:	VALID
Title in English:	Plain bearings—Quality control techniques and inspection of geometrical and material quality characteristics
Title in Chinese:	滑动轴承几何和材料质量特性的质量控制技术和检验
Language:	English
File Format:	Electronic (PDF)
Delivery:	Via email within 8 business days
Issued on:	2011-12-30
Implemented on:	2012-10-01
ICS Classification:	21.100.10-Plain bearings
Chinese Classification:	J12-Sliding bearing
Professional Classification:	GB-National Standard
Related Keywords:	plain bearings quality control techniques quality control techniques material quality characteristics material quality characteristics scopethis standard flangeless bearings
Related Topics:	Impurities linear several Quality Inspection Technology of the Future Material mass activity material quality material quality quality control technology quality characteristics Shaft Quality Inspection GBT27939 GB/T 27939-2011 How to check the quality of tvoc sensor Quality of Liposome Preparation Technology Mass flow controller calibration standards Establishment and quality control of mass spectrometry detection methods gb/t 27939-2011 gb/t 27939 gb 27939

《GB/T 27939-2011滑动轴承几何和材料质量特性的质量控制技术和检验》由TC236（全国滑动轴承标准化技术委员会）归口，主管部门为中国机械工业联合会。

Scope

This standard specifies the quality control techniques and inspections for the geometrical and material quality characteristics of the following types of sliding bearings: - metal thin-walled flanged and flangeless bearings as specified in ISO 3548; Ratio of thickness to outer diameter S3: D_o>O.11 flanged and non-flange metal thick-walled bearing bushes; — Coiled bushings that comply with the ISO 3547 series standards; — Single-layer or multi-layer - Integral metal bushings with flanges and without flanges, made of multi-layer materials, whose outer diameter D_o is not greater than 230 mm; - Integral thermoplastics with flanges and without flanges, with inner diameter D_i≤200 mm Shaft sleeves; —full circle and semicircular thrust washers in accordance with ISO 6525 and ISO 6526; —sintered shaft sleeves in accordance with ISO 2795.

More samples: JGJ 94-2008 NB/T 47013.2-2015 YD/T 3934-2021

Sample only — not a preview of GB/T 27939-2011

Loading PDF document...

Error loading PDF. Please make sure the file is valid and try again.

We also recommend

GB/T 37169-2018 in English

Metal mesh based PTFE strip specification and test methods
2018-12-28
GB/T 18325.1-2025 in English

Plain bearings—Bearing fatigue—Part 1:Plain bearings in test rigs and in applications under conditions of hydrodynamic lubrication
2025-10-31
GB/T 47254-2026 in English

Plain bearings—Dynamic adhesion test method for DLC coated parts under lubricated condition
2026-02-27
GB/T 43324-2023 in English

Foil bearings—Performance of hydrodynamic gas thrust bearings—Testing of static load capacity, bearing torque , friction coefficient and lifetime
2023-11-27
GB/T 18323-2022 in English

Plain bearings—Sintered bushes—Dimensions and tolerances
2022-12-30
GB/T 34633.1-2017 in English

Plain bearings-Pedestal plain bearings-Part 1:Pillow blocks
2017-11-01
GB/T 39333-2020 in English

Plain bearings—Quality assurance of sample types—Definitions, applications and testing
2020-11-19
GB/T 23891.1-2009 in English

Plain bearings—Hydrodynamic plain thrust pad bearings under steady-state conditions—Part 1:Calculation of thrust pad bearings
2009-05-26
GB/T 39142.1-2020 in English

Specification of plastic-steel bilayer self-lubricating materials—Part 1:Running-in layer with modified PTFE tape
2020-10-11
GB/T 7308.1-2021 in English

Plain bearings—Thin-walled half bearings with or without flange—Part 1：Tolerances, design features and methods of test
2021-03-09