Instrument Validation Scope

Instrument Validation Scope, Total:138 items.

The international standard classification for "Instrument Validation Scope" includes: Optical equipment , Radiation protection , Acoustics and acoustic measurements , Electronic display devices , Non-destructive testing , Metrology and measurement in general , Quality management and quality assurance .

The Chinese standard classification for "Instrument Validation Scope" includes: Optical instrument in general , Radiation protection instrument , Acoustic instrument and seismograph , Ultrasonic wave and sound radiation defectoscope , Basic standards and general methods , Display recording instrument , Industrial automation and control device in general .

General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China

GB/T 14318-2008 Radiation protection instrumentation—Neutron ambient dose equivalent(rate)meters
GB/T 32706-2016 Safety requirements for laboratory instrument and equipment-Noise measuring instruments
GB/T 12085.1-2010 Optics and optical instruments - Environmental test methods - Part 1:Definitions extent of testing
GB/T 12851-1991 Blank detail specification of twisted nematic liquid crystal displays for instruments
GB/T 32704-2016 Safety requirements for laboratory instrument and equipment-Balance instruments
GB/T 12085.1-1989 Optics and optical instruments--Environmental test methods--Definitions extent of testing

Professional Standard - Agriculture

CNAS-GL040-2019 Instrument Validation Implementation Guide
RB/T 223-2023 Guidelines for the Validation and Evaluation of Domestic Testing Instruments and Equipment Gas Chromatograph

Shanxi Provincial Standard of the People's Republic of China

DB1404/T 17-2021 Inspection and testing laboratory instrument analytical method validation requirements chromatography
DB1404/T 18-2021 Inspection and testing laboratory instrument analysis method validation requirements Spectroscopy

Group Standards of the People's Republic of China

T/CAQI 108-2020 Specification for verification and evaluation of portable Raman spectrometer
T/CAQI 110-2020 Specification for verification and evaluation of polymerase chain reaction amplifier
T/SUCA 045-2023 High-Dynamic Range（HDR）display certification technical specification
T/CAQI 107-2020 General Rule for Verificaiton and Evaluation of Analytical Instrument
T/CAQI 328-2023 Specification for verification and evaluation of nitrogen generators for liquid chromatography mass spectrometers
T/SUCA 044-2023 HDR LED display certification technical specification
T/CAQI 111-2020 Specification for verification and evaluation of Solid Phase Extractor
T/CCAS 006-2018 Validation and comprehensive evaluation specification of laser particle size analyzer (wet method)

Xinjiang Provincial Standard of the People's Republic of China

DB65/T 3920-2016 Cotton quality instrumentation notarization inspection laboratory construction and management specifications

中华人民共和国国家质量监督检验检疫总局、中国国家标准化管理委员会

GB/T 33888-2017 Non-destructive testing instruments--Characterization and verification of ultrasonic thickness measuring equipment

Professional Standard - Machinery

JB/T 9266-1999 Temperature measuring range of indicating instruments and recording instruments
JB/T 9233.19-1999 General methods of testing the performance of industrial process measurement and control instruments Zero and span adjustable range
JB/T 6214-2014 Guide to the Reliability Compliance Test and Determination Test(Exponential Distribution)of Instrumentation
JB/T 6214-1992 Guideline for Reliability Validation Test and Determination Test (Exponential Distribution) for Instrumentation
JB/T 9233.10-1999 General methods of testing the performance of industrial process measurement and control instruments Overrange effect

机械工业部

JB/T 56214-1992 Guidelines for instrument reliability verification tests and measurement tests (exponential distribution)

Professional Standard - Geology

DZ/T 0198.11-1997 Guideline for geological instrument process management - process verification

国家市场监督管理总局、中国国家标准化管理委员会

GB/T 14318-2019 Radiation protection instrumentation—Neutron ambient dose equivalent(rate)meters

Professional Standard - Certification and Accreditation

RB/T 160-2017 Guidance on verification and overall evaluation of analytical chemistry instrument

Professional Standard - Ocean

HY/T 141-2011 Specification for sea test of oceanographic instruments

Henan Provincial Standard of the People's Republic of China

DB4112/T 310-2022 Verification specification for calibration capability of elevator speed limiter

German Institute for Standardization

DIN 2271-3:1976 Verification of geometrical parameters - Pneumatic length measurement (air gauging) - Part 3: Characteristics of instruments working in the high-pressure range - requirements, testing
DIN 2271-3:2000 Verification of geometrical parameters - Pneumatic length measurement (air gauging) - Part 3: Characteristics of instruments working in the high-pressure range - requirements, testing
DIN 58395:1976 Temperature ranges for lubricants for optical instruments
DIN 45662:1996 Vibration measuring instrumentation - Fundamental requirements and verification
DIN 45662:1996-12 Vibration measuring instrumentation - Fundamental requirements and verification
DIN 2271-2:1976 Pneumatic Length Measurement (Air Gauging); Design Features of Instruments Working in the High Pressure Range
DIN 12771:1971 Laboratory glassware; enclosed scale colorimeter thermometers of 6 degC range
DIN 58700-2:1978 ISO-fits; selection of tolerance zones for fine-mechanics, recommended fits
DIN 12836-3:1975 Apparatus for dairy analyses; milk butyrometer 0 to 10 %, calibrated
DIN 12789:1972 Laboratory glassware; Beckmann thermometers, adjustable range enclosed scale thermometers
DIN EN 12668-1:2000 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments
DIN EN ISO 376:2011-09 Metallic materials - Calibration of force-proving instruments used for the verification of uniaxial testing machines (ISO 376:2011); German version EN ISO 376:2011 / Note: DIN EN ISO 376 (2005-02) remains valid alongside this standard until 2011-12-31.
DIN EN 12668-1:2010 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments; German version EN 12668-1:2010

British Standards Institution (BSI)

BS 1794:1952(1999) Specification for Chart ranges for temperature recording instruments
BS 1794:1952 Specification for chart ranges for temperature recording instruments
BS IEC 61501:2001 Nuclear reactor instrumentation - Wide range neutron fluence rate meter - Mean square voltage method
BS 7516:1995 Nuclear instrumentation. Liquid-scintillation counting systems. Performance verification
19/30387015 DC BS IEC 63175. Nuclear instrumentation. Fixed high intensity proton cyclotron within the energy range of 10 ~ 20 MeV
BS EN 12668-1:2010 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Instruments
BS EN 12668-1:2000 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Instruments
19/30402906 DC BS EN IEC 63175. Nuclear instrumentation. Fixed high intensity proton cyclotron within the energy range of 10 ~ 20 MeV
BS EN ISO 18563-1:2015 Non-destructive testing. Characterization and verification of ultrasonic phased array equipment. Instruments
BS EN ISO 15548-1:2013 Non-destructive testing. Equipment for eddy current examination. Instrument characteristics and verification

SCC

BS ISO 9022-1:1994 Optics and optical instruments. Environmental test methods-Definitions, extent of testing
DIN IEC 61304:1996 Nuclear instrumentation - Liquid-scintillation counting systems - Performance verification (IEC 61304:1994)
NS-EN 13860-1:2003 Non destructive testing — Eddy current examination — Equipment characteristics and verification — Part 1: Instrument characteristics and verification
NS 848:1954 Area and volumes of buildings — Rules for measurement
DANSK DS/EN ISO 376:2011 Metallic materials - Calibration of force-proving instruments used for the verification of uniaxial testing machines

VN-TCVN

TCVN 4382-1986 Measuring equipments.Verification schedule.Scope and layout

GOST

GOST R 8.763-2011 State system for ensuring the uniformity of measurements. State verification schedule for measuring instruments of length in the range from 1·10-9 to 50 m and wavelength in the range from 0, 2 to 50 µm
GOST 8.233-1977 State system for ensuring the uniformity of measurements. State special standard and all-union verification schedule for measuring means of sound pressure in water medium of frequency range 0,01-1 hz

BSI

SN-CWA 18133:2024 Raman instruments calibration and verification protocols

Korean Agency for Technology and Standards (KATS)

KS B ISO 9022-1:2003 Optics and optical instruments-Environmental test methods-Patr 1:Definitions, extent of testing
KS B ISO 9022-1:2013 Optics and optical instruments ― Environmental test methods ― Part 1: Definitions, extent of testing

RU-GOST R

GOST R 8.841-2013 State system for ensuring the uniformity of measurement. Instruments for measurement of exposure and irradiance in the wavelength range 1 to 10 nm. Verification procedure
GOST R 8.867-2014 State system for ensuring the uniformity of measurement. Measuring instruments of direct current in range from 1·10 v stepeni -15 to 1·10 v stepeni -9 A. Verification procedure
GOST 8.551-2013 State system for ensuring the uniformity of measurements. State verification schedule for measuring instruments of electrical power and energy in the frequency range from 1 to 2500 Hz
GOST R 8.746-2011 State system for ensuring the uniformity of measurements. State verification schedule for instruments measuring the ratio error and phase displacement of a.c. power frequency voltage in the range from 0,1/V3 do 750/V3 kB
GOST R 8.870-2014 State system for ensuring the uniformity of measurements. State verification schedule for instruments measuring of sound velocity in liquids within the velocity range 800 to 2000 m/s
GOST R 8.863-2013 State system for ensuring the uniformity of measurements. Insruments for measurement power and irradiance in the wavelength range from 10 to 30 nm. Verification procedure
GOST R 8.817-2013 State system for ensuring the uniformity of measurements. State verification schedule for measuring instruments of standard lightning and switching impulse electrical voltage in the range from 1 to 1000 kV
GOST R 8.711-2013 State system for ensuring the uniformity of measurements. State verification schedule for measuring instruments of complex dielectric permittivity in range of frequencies from 1 to 178,4 GHz
GOST 8.322-1978 State system for ensuring the uniformity of measurements. Measuring signal generators. Methods and means for verification within the range of 0.03-17.44 GHz
GOST 8.296-2015 State system for ensuring the uniformity of measurements. State verification schedule for instruments measuring the surface roughness parameters Rmax, Rz in the range from 0,001 to 3000 mm and Ra in range from 0,001 to 750 mm
GOST R 8.796-2012 State system for ensuring the uniformity of measurements. Torque measuring devices. Verification procedure
GOST R 56510-2015 Metrological assurance in the field of non-destructive testing
GOST R 8.875-2014 State system for ensuring the uniformity of measurements. State verification schedule for measuring instruments of the phase shift angle between two electric signals in the range of frequencies from 0,1 MHz to 65 GHz
GOST R 8.648-2015 State system for ensuring the Uniformity of measurements. State verification schedule for measuring instruments of alternate electrical voltage to 1000 V in the frequency range from 1·10-2 to 2·10-9 Hz
GOST 12441-1966 Horisontal length comparators. Methods and means for verification
GOST R 8.797-2012 State system for ensuring the uniformity of measurements. State verification scheme for instruments measuring the heat flux surface density in the range from 1 to 10000 W/m2
GOST 8.641-2014 State system for ensuring the uniformity of measurements. State verification schedule for measuring instruments of power of electromagnetic oscillations in coaxial and waveguide lines in the frequency range 0,03 to 37,5 GHz
GOST 8.102-1973 State system for ensuring the uniformity of measurements. The state standard and all-union verification schedule for instruments measuring power of electromagnetic oscillations in waveguides within frequency range from 37,5 up to 53,57 GHz

International Organization for Standardization (ISO)

ISO 9022-1:1994 Optics and optical instruments - Environmental test methods - Part 1: Definitions, extent of testing

Association Francaise de Normalisation

NF E05-059-1:2003 Geometrical products specification (GPS) - Acceptance tests and reverification tests of profile measuring instruments - Part 1 : measuring instruments for areal surface texture.
NF A09-170-1:2008 Non-destructive testing - Equipment for eddy current examination - Part 1 : instrument characteristics and verification.

American Society for Testing and Materials (ASTM)

ASTM RR-E28-1009 1989 E0074-Practices for Calibration and Verification for Force-Measuring Instruments
ASTM E74-18 Standard Practices for Calibration and Verification for Force-Measuring Instruments
ASTM E74-18e1 Standard Practices for Calibration and Verification for Force-Measuring Instruments
ASTM E2214-08 Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments
ASTM E2214-16 Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments
ASTM E2214-19 Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments
ASTM E2214-18 Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments
ASTM E2214-20 Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments
ASTM E2214-17 Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments

Defense Logistics Agency

DLA MIL-HDBK-816 VALID NOTICE 1-2007 GUIDELINES FOR DEVELOPING RADIATION HARDNESS ASSURANCE DEVICE SPECIFICATIONS
DLA MIL-HDBK-816 VALID NOTICE 2-2007 Guidelines for Developing Radiation Hardness Assurance Device Specifications
DLA MIL-HDBK-816 CHG NOTICE 1-2002 GUIDELINES FOR DEVELOPING RADIATION HARDNESS ASSURANCE DEVICE SPECIFICATIONS

CZ-CSN

CSN 25 6112-2004 Measuring device for lenght measuring of fabric - Methods for verification
CSN 25 6112-1986 Measuring device for length measuring of abric. Methods for verification

GSO

BH GSO IEC 61304:2016 Nuclear instrumentation - Liquid-scintillation counting systems - Performance verification
OS GSO IEC 61304:2015 Nuclear instrumentation - Liquid-scintillation counting systems - Performance verification
GSO OIML R147:2021 Standard blackbody radiators for the temperature range from –50 °C to 2500 °C - Calibration and verification procedures
BH GSO ASTM E74:2023 Standard Practices for Calibration and Verification for Force-Measuring Instruments
GSO ASTM E74:2022 Standard Practices for Calibration and Verification for Force-Measuring Instruments
OS GSO OIML D20:2009 Initial and subsequent verification of measuring instruments and processes
GSO OIML D20:2009 Initial and subsequent verification of measuring instruments and processes
OS GSO OIML R141:2013 Procedure for calibration and verification of the main characteristics of the thermographic instruments
BH GSO OIML R141:2015 Procedure for calibration and verification of the main characteristics of the thermographic instruments
GSO ISO 15253:2013 Ophthalmic optics and instruments -- Optical devices for enhancing low vision

Japanese Industrial Standards Committee (JISC)

JIS B 7728:1997 Calibration of force-proving instruments used for the verification of uniaxial testing machines
JIS B 7728:2013 Calibration of force-proving instruments used for the verification of uniaxial testing machines
JIS B 7728:2002 Calibration of force-proving instruments used for the verification of uniaxial testing machines

International Electrotechnical Commission (IEC)

CISPR 16-1-5-2003/AMD1-2012 Amendment 1 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Specifications and validation procedures
CISPR 16-1-5:2003/AMD1:2012 Amendment 1 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Specifications and validation procedures
IEC 61304:1994 Nuclear instrumentation - Liquid-scintillation counting systems - Performance verification
IEC 60323:1970 Analogue voltage ranges and logic levels for mains operated nuclear instruments

SE-SIS

SIS SMS 1341-1950 Instrument, maximum tolerance range, standard diameter exceeds 6-18
SIS SMS 1339-1950 Instrument, maximum tolerance range, maximum standard diameter exceeds 6-18
SIS SMS 1342-1950 Instrument, maximum tolerance range, minimum standard diameter exceeds 18-180

DIN

DIN ISO 9022-1:1999 Optics and optical instruments - Environmental test methods - Part 1: Definitions, extent of testing (ISO 9022-1:1994)

Lithuanian Standards Office

LST EN ISO 376:2011 Metallic materials - Calibration of force-proving instruments used for the verification of uniaxial testing machines (ISO 376:2011)

Spanish Association for Standardization (UNE)

UNE-EN ISO 376:2011 Metallic materials - Calibration of force-proving instruments used for the verification of uniaxial testing machines (ISO 376:2011)
UNE-EN 13860-1:2003 Non destructive testing. Eddy current examination. Equipment characteristics and verification. Part 1: Instrument characteristics and verification

US-CFR-file

CFR 46-189.25-10-2014 Shipping. Part189:Inspection and certification. Section189.25–10:Scope of inspection.

Indonesia Standards

SNI 18-7027-2004 Nuclear instrumentation - Liquid scintillation counting systems - Performance verification

North Atlantic Treaty Organization Standards Agency

STANAG 3436-1985 COLOURS AND MARKINGS USED TO DENOTE OPERATING RANGES OF AIRCRAFT INSTRUMENTS

European Committee for Standardization (CEN)

EN 13860-1:2003 Non destructive testing - Eddy current examination - Equipment characteristics and verification - Part 1: Instrument characteristics and verification
EN 12668-1:2010 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments

CU-NC

NC 90-06-39-1984 Metrologleal Assuranoe. Welghing Instrumenta for Plece Computation. Verifioation Methods and Means

Danish Standards Foundation

DS/EN ISO 376:2011 Metallic materials - Calibration of force-proving instruments used for the verification of uniaxial testing machines

Standard Association of Australia （SAA）

AS 3129:1981 Approval and test specification for electric fence controllers

YU-JUS

JUS N.A5.041-1987 Verification mechanical strength resistance ageinst impact. Impact-test apparatus

Engineering Equipment and Materials Users Association （EEMUA)

EEMUA PUB NO 175-2013 EEMUA Code of Practice Calibration and validation of process analysers (Edition 2)

EEMUA - Engineering Equipment and Materials Users Association

PUB NO 175-2013 EEMUA Code of Practice Calibration and validation of process analysers (Edition 2)

IEEE - The Institute of Electrical and Electronics Engineers@ Inc.

IEEE C63.2-2016 Specifications of Electromagnetic Interference and Field Strength Measuring Instrumentation in the Frequency Range 9 kHz to 40 GHz

Institute of Electrical and Electronics Engineers (IEEE)

IEEE Std C63.2-2009 American National Standard for Electromagnetic Noise and Field Strength Instrumentation, 10 Hz to 40 GHz Specifications

American Bureau of Shipping

ABS 69-1993 Certification of Oil Spill Recovery Equipment