Test group Verification group

Test group Verification group, Total:372 items.

The international standard classification for "Test group Verification group" includes: Power stations in general , Environmental testing , Solar energy engineering , Exploratory and extraction equipment , Gas and steam turbines, Steam engines , Wires , Components for aerospace construction .

The Chinese standard classification for "Test group Verification group" includes: Electric power system equipment installation testing , Ambient conditions , Solar energy , Physical power source , Petroleum drilling & production equipment and instrument , Other generating equipment , Wire with insulation layer , Basic standards and general methods , Railway components , Pump , Electronic components , Pipe fittings, clamps and seals , Technical management .

未注明发布机构

NB/T 31053-2014 Modeling and Validation Method of Wind Turbine Low Voltage Ride Through Characteristics
DIN 38402-42:1984 German standard methods for the examination of water, waste water and sludge - General informations (group A) - Part 42: Interlaboratory trials for method validation, evaluation (A 42)
DIN CEN/TS 764-8:2016*DIN SPEC 2930:2016 Pressure equipment and assemblies - Part 8: Proof test
DIN EN 12668-3:2000 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment

机械电子工业部

JB/T 5149-1991 Test methods for combined air handling units

Professional Standard - Energy

NB/T10656-2021 Simulation and verification of vibration stability of direct drive permanent magnet wind turbine generator
NB/T 31053-2021 Code of practice for electrical simulation model validation of wind turbines
NB/T 42094-2016(英文版) Electrical test procedures for small hydropower units
NB/T 42052-2015 Specification for small hydropower unit starting test

Taiwan Provincial Standard of the People's Republic of China

CNS 10930-1984 Method of Test for Fiber Optic Devices (Dust (Fine Sand) Test)
CNS 11237-1985 Sealing (Immersion Cyclic) Testing Method for Electronic Components
CNS 11704-1986 Method of Test for Fiber Optic Devices (FOTP-15 Altitude Immersion Test)
CNS 10878-1984 Method of Test for Fiber Optic Devices (Impact Testing of Cable Assemblies)
CNS 7640-1981 Optical fiber component inspection method – optical cable retention test of relay connection components
CNS 12566-1993 Basic Environmental Testing Procedures Part 2: Tests, Test Z/AD:Composite Temperature/Humidity Cyclic Test
CNS 3626-1985 Voltage Endurance Testing Method for Electronic Components
CNS 10929-1984 Method of Test for Fiber Optic Devices (Circuit Discontinuities Test)
CNS 10931-1984 Method of Test for Fiber Optic Devices (Cable Wicking Test)
CNS 11333-1985 Method of Test for Fiber Optic Devices (Fiber Optic Cable Fluid Immersion Test)
CNS 10925-1984 Method of Test for Fiber Optic Devices (Fluid Immersion Test)
CNS 10877-1984 Method of Test for Fiber Optic Devices (Maintenance Aging)
CNS 10876-1984 Method of Test for Fiber Optic Devices (Vibration Test)
CNS 3635-1985 Insulation Resistance Testing Method for Electronic Components
CNS 2514-1990 Method of Test for Fiber Composition of Pulp and Paper
CNS 7639-1981 Method of Test for Fiber Optic Devices Humidity Test Procedure for Fiber Optic Connecting Devices
CNS 10924-1984 Method of Test for Fiber Optic Devices (Tensile Proof Test)
CNS 8264-1982 Vibration Test Methods for Parts of Railway Rolling Stock
CNS 14129-1998 Method of random vibration test for vehicle parts
CNS 7137-1997 Sine-vibration testing method for automobile parts
CNS 12084-1987 Method of Test for Fiber Optic Devices (FOPT-36 Twist Test for Fiber Optic Cable Assemblies
CNS 11703-1986 Method of Test for Fiber Optic Devices (FOTP-14 Shock Test, Specified Pulse)
CNS 8265-1982 Shock Test Methods for Parts of Railway Rolling Stock

国家铁路局

TB/T 3453.2-2016 EMU/DMU vocabulary-Part 2:Test
TB/T 3407-2015 Test method for EMU bogie axle box composition
TB/T 3500-2018 EMU car body crashworthiness requirements and verification specifications

国家能源局

NB/T 42094-2016 Electrical test code for small hydropower units
NB/T 42131-2017 Environmental testing requirements for photovoltaic modules. General principles
NB/T 10587-2021 Verification code of power curve for wind turbine in wind farm
NB/T 10270-2019 Performance acceptance test code on geothermal power unit

Professional Standard - Water Conservancy

SL 237-069-1999 Soil Test Procedures - Mineral Composition Tests of Soils

Professional Standard - Electricity

DL/T 507-2002 Start-up Test Code for Hydraulic-turbine and Generator Units
DL/T 507-2014 Testing Regulations for Hydroelectric Generating Set Start-up
DL/T 851-2004 Acceptance tests for combined-cycle power plants
DL 507-1993 Regulations for start-up test of hydro-generator set
DL/T 1616-2016 Guide Rule for Property Test of Thermal Power Generating Units

Professional Standard - Aerospace

QJ 2630.3-1994 Space environment test method for satellite components Vacuum discharge test
QJ 2630.4-1996 Space encironment test methods for satellite components.Megnetic test
QJ 2630.2-1994 Satellite component space environment test method heat balance test
QJ 2630.5-1998 Space Environment Test Methods for Satellite Components Vacuum Cold-Welding Test
QJ 2630.1-1994 Space environment test method for satellite components Thermal vacuum test

General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China

GB/T 4074.8-2009 Winding wires - Test methods - Part 8: Test procedure for the determination of the temperature index of enamelled winding wires - Quick-Test method
GB/T 2423.34-2012 Environmental testing - Part 2: Test methods - Test Z/AD: Composite temperature/humidity cyclic test
GB/T 2423.34-2024 Environmental testing—Part 2:Test methods—Test Z/AD: Composite temperature/humidity cyclic test
GB/T 18912-2002 Salt mist corrosion testing of photovoltaic(PV) modules
GB/T 30555-2014 Rules for Screw Expander (Unit) Thermal Acceptance Test
GB/T 14999.4-1994 Methods of examining micro - Structures for heat - Resisting superalloys
GB/T 4074.7-2009 Winding wires - Test methods - Part 7: Test procedure for the determination of the temperature index of enamelled winding wires
GB/T 18451.2-2003 Wind turbine generator systems - Wind turbine power performance testing
GB/T 16750.3-1997 The test method for electrical submersible pump units
GB/T 43058-2023 Ammonia corrosion testing of photovoltaic(PV) modules
GB/T 19394-2003 UV test for photovoltaic (PV) modules
GB/T 43057-2023 Photovoltaic (PV) modules—Dynamic mechanical load testing

Group Standards of the People's Republic of China

T/CEEMA 002-2020 Technical specification for wind turbine power curve verification

未注明发布机构

DIN CEN/TS 764-8:2016*DIN SPEC 2930:2016 Pressure equipment and assemblies - Part 8: Proof test
NB/T 31053-2014 Modeling and Validation Method of Wind Turbine Low Voltage Ride Through Characteristics
DIN 38402-42:1984 German standard methods for the examination of water, waste water and sludge - General informations (group A) - Part 42: Interlaboratory trials for method validation, evaluation (A 42)
DIN EN 12668-3:2000 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment

Professional Standard - Railway

TB/T 3348-2014 Traction characteristics test methods for EMU
TB/T 2711-2015 Test method for air compressor set on locomotive and EMU/DMU
TB/T 3345-2014 Starting and accelerating test methods for EMU
TB/T 2491-1994 Test Method for Fastener Assembly Fatigue
TB/T 3250-2010 Specifications of Sealing Design and Test for Powered Car Train-Set

Professional Standard - Machinery

JB/T 6882-1993 Pump reliability verification test
JB/T 6882-2006 Pump reliability verification test
JB/T 7080-1993 Testing instrument for winding inter-turn impulse voltage
JB/T 9818.2-1999 Test methods for combined husker and whitener united rice mill
JB/T 7315-1994 Test method for compound feed processing unit
JB/T 4279.6-1994 Enamelled winding wire test equipment equipment verification method peeling tester
JB/T 7323-1994 Test methods for wind turbines

中国石油天然气总公司

SY/T 5808-1993 Assembly and test procedures for electric submersible pumps

国家市场监督管理总局、中国国家标准化管理委员会

GB/T 37663.1-2019 Outdoor empirical test requirements for distributed photovoltaic in warm damp climate—Part 1: Photovoltaic module
GB/T 38314-2019 Lithium ion battery design and verification requirements for space application

Professional Standard - Aviation

HB 7044-1994 Fire Protection Test of Hose and Rigid Pipe Assembly

Professional Standard - Electron

SJ/T 10669-1995 Solderability tests for surface mounted devices
SJ/Z 9001.10-1987 Basic environmental testing procedures--Part 2: Tests--Test Z/AD: Composite temperature/humidity cyclic test

Korean Agency for Technology and Standards (KATS)

KS I ISO 14066-2016(2021) Greenhouse gases -- Competence requirements for greenhouse gas validation teams and verification teams
KS C 3003-1982 Methods of test for fiber or paper insulated copper and aluminum winding wires
KS C 3003-1998 Methods of test for fiber or paper insulated copper and aluminum winding wires
KS F 2268-1-2014(2020) Fire resistance test for door assemblies
KS F 2268-1-2021 Fire resistance test for door assemblies
KS I ISO 16431-2020 Hydraulic fluid power－Assembled systems－Verification of cleanliness
KS P 1011-2008 Test method of the 2-D electrophoresis for recombinant bacteria
KS C 0233-2001(2016) Environmental testing Part 2：Tests－ Test Z/AM：Combines cold/low air pressure tests
KS C 0234-2001(2016) Environmental testing Part 2：Tests－ Test Z/BM：Combined dry heat/low air pressure tests
KS B ISO 8956:2013 Acceptance conditions for copying attachments, integral or otherwise, for lathes－Testing of the accuracy
KS B ISO 8956:2004 Acceptance conditions for copying attachments, integral or otherwise, for lathes-Testing of the accuracy
KS V 0820-2001(2011) Fire resistance of hose assemblies－Test methods
KS V ISO 15540-2006(2016) Fire resistance of hose assemblies－Test methods
KS C IEC 61701:2014 Salt mist corrosion testing of photovoltaic(PV) modules
KS D 0210-1992 MacroStructure Detecting Method for Steel
KS C IEC 61701:2005 Salt mist corrosion testing of photovoltaic(PV) modules
KS C IEC 60068-2-38:2014 Environmental testing — Part 2-38: Tests — Test Z/AD: Composite temperature/humidity cyclic test
KS C IEC 61189-5-2020 Test methods for electrical materials, interconnection structures and assemblies－Part 5：Test methods for printed board assemblies
KS B ISO 3452-3:2006 Non-destructive testing-Penetrant testing-Part 3:Reference test blocks
KS C IEC 61189-5-2009(2020) Test methods for electrical materials, interconnection structures and assemblies－Part 5：Test methods for printed board assemblies
KS C IEC 62716:2014 Photovoltaic(PV) modules — Ammonia corrosion testing
KS V ISO 15540:2006 Fire resistance of hose assemblies－Test methods
KS M 5468-1984 Test methods for dilution of components in lacquer
KS B 5525-2022 Vickers hardness testing machines(Verification of testing mechine)
KS E ISO 8865:2002 Mining－Guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
KS B 5525-2002(2017) Vickers hardness testing machines(Verification of testing mechine)
KS E ISO 8865:2022 Mining — Guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
KS V ISO 15540-2006(2021) Fire resistance of hose assemblies－Test methods
KS B 5525-2002(2022) Vickers hardness testing machines(Verification of testing mechine)
KS C IEC 61189-5:2009 Test methods for electrical materials, interconnection structures and assemblies－Part 5：Test methods for printed board assemblies
KS C IEC 60068-2-82:2021 Environmental testing — Part 2-82: Tests — Test Xw1: Whisker test methods for components and parts used in electronic assemblies
KS C IEC 61189-6-2020 Test methods for electrical materials, interconnection structures and assemblies－Part 6：Test methods for materials used in manufacturing electronic assemblies

ASHRAE - American Society of Heating@ Refrigerating and Air-Conditioning Engineers@ Inc.

ASHRAE PH-97-3-3-1997 GAX Component Simulation and Validation
ASHRAE 4689-2004 Thermodynamic Modeling and Experimental Validation of Screw Liquid Chillers
ASHRAE SF-98-21-1-1998 Experimental Results and Modeling Tests of an Adsorptive Air-Conditioning Unit
ASHRAE 182-2008 Method of Testing Absorption Water-Chilling and Water-Heating Packages

SAE - SAE International

SAE AS5688A-2004 Cable Assemblies; Aircraft@ Proof Testing and Prestretching of
SAE AS2094B-2018 Test Methods for Tube-Fitting Assemblies
SAE J1549-2021 Diesel Fuel Injection Pump - Validation of Calibrating Nozzle Holder Assemblies@ Recommended Practice

GB-REG

REG NASA-LLIS-3763-2011 Lessons Learned - Certifying Calibration on Test Components

European Committee for Standardization (CEN)

CEN/TS 764-8:2016 Pressure equipment and assemblies - Part 8: Proof test
EN ISO 8032:1999 Rubber and Plastics Hose Assemblies - Flexing Combined with Hydraulic Impulse Test (Half-Omega Test)
EN ISO 16964:2020 Gas cylinders - Flexible hoses assemblies - Specification and testing (ISO 16964:2019)
EN 13741:2003 Thermal performance acceptance testing of mechanical draught series wet cooling towers

SCC

DANSK DS/CEN/TS 764-8:2016 Pressure equipment and assemblies – Part 8: Proof test
SN-CEN/TS 764-8:2016 Pressure equipment and assemblies — Part 8: Proof test
DANSK DS/ISO 8269:1986 Doorsets - Static loading test
MIL MIL-DTL-5688E-2001 WIRE ROPE ASSEMBLIES; AIRCRAFT, PROOF TESTING AND PRESTRETCHING OF (SUPERSEDING MIL-DTL-5688D)
BS PD ISO/TS 16431:2002 Hydraulic fluid power. Assembled systems. Verification of cleanliness
AS C73.4:1969 Magnet winding wire - Test requirements
CEI 13-71:2015 Electrical energy measurement systems (AC) - Guide to composition, installation and verification
AS C73.3:1969 Magnet winding wire - Test methods
AS/NZS 4266.11:1995 Reconstituted wood-based panels - Methods of test, Method 11: Wet cyclic test (V313 test)
AS B128:1963 Verification of testing machines
CEI 13-4:2005 Electrical energy measurement systems - Composition, precision and verification - SEE SUMMARY
BS EN 60851-5:1998 Winding Wires. Test methods-Electrical properties
BS EN 60851-6:1998 Methods of test for winding wires-Thermal properties
BS PD IEC TS 63209-2:2022 Photovoltaic modules. Extended-stress testing-Polymeric component materials
BS 2885:1957 Code for acceptance tests on stationary steam generating units
BS 1610-1:1950 Verification of testing machines. Methods of load verification verification tensile and compression testing
BS 6811-2-2.5:1987 Winding wires. Methods of test-Electrical properties
BS EN 60851-4:1995 Methods of test for winding wires-Chemical properties
BS 6811-2-2.3:1992 Winding wires. Methods of test-Mechanical properties
BS EN 60851-3:1998 Methods of test for winding wires-Mechanical properties
BS 6811-2-2.3:1987 Winding wires. Methods of test.-Mechanical properties
BS 6811-2-2.5:1992 Winding wires. Methods of test-Electrical properties
BS 5173-102-102.1:1991 Methods of test for rubber and plastics hoses and hose assemblies. Hydraulic pressure tests-Hydrostatic tests
CEI 48-4:1983 Electromechanical components for electronic equipment. Basic test procedures and measurement methods. 2 Group of tests
CEI 48-9:1988 Electromechanical components for electronic equipment. Basic test procedures and measurement methods. 4 Group of tests
CEI 48-3:1982 Electromechanical components for electronic equipment. Basic test procedures and measurement methods. 1 Group of tests
DANSK DS/EN 60439-1:2001 Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies
BS 5350-C10:1979 Methods of test for adhesives-90° peel test for a flexible-to-rigid assembly
CEI EN 60439-1:2000 Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies
BS EN 60439-1:1994 Specification for low-voltage switchgear and controlgear assemblies-Specification for type-tested and partially type-tested assemblies
BS 5350-C12:1979 Methods of test for adhesives-180° 'T' peel test for a flexible-to-flexible assembly
BS 1610-1:1958 Verification of testing machines. Methods of load verification requirements for elastic proving devices and verification of machines for tension and compression testing
BS 2011-2.1Z/BFC:1984 Environmental testing. Tests-Tests Z/BFc. Combined dry heat/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
UNE-EN 60439-1:2001 Low-voltage switchgear and controlgear assemblies -- Part 1: Type-tested and partially type-tested assemblies.
BS 5173-4:1977 Methods of test for rubber and plastics hoses and hose assemblies-Electrical tests
MIL MIL-DTL-5688C-1999 WIRE ROPE ASSEMBLIES; AIRCRAFT, PROOF TESTING AND PRESTRETCHING OF (SUPERSEDING MIL-DTL-5688B) (S/S BY MIL-DTL-5688D)
MIL MIL-DTL-5688B-1997 WIRE ROPE ASSEMBLIES; AIRCRAFT, PROOF TESTING AND PRESTRETCHING OF (SUPERSEDING MIL-C-5688A) (S/S BY MIL-DTL-5688C)

Association Francaise de Normalisation

XP E01-201-8*XP CEN/TS 764-8:2016 Pressure equipment and assemblies - Part 8 : proof test
XP E01-201-8-2016 Pressure equipment and assemblies - Part 8 : proof test
NF EN IEC 60068-2-82:2019 Environmental testing - Part 2-82: testing - Test Xw1: whisker verification methods for components and parts used in electronic assemblies
NF EN 17038-2:2019 Pumps - Methods for qualifying and verifying the energy efficiency index of rotodynamic pump sets - Part 2: tests and calculation of the energy efficiency index (EEI) of simple pump sets
FD X30-148:2016 Measurement and verification of the energy performance - Determination of energy savings in organizations
NF E29-666:2014 Transportable gas cylinders - Cylinder bundles - Periodic inspection and testing
NF EN ISO/IEC 17043:2010 Conformity assessment - General requirements for the competence of proficiency test organizers
NF C20-738*NF EN 60068-2-38:2010 Environmental testing - Part 2-38 : tests - Test Z/AD : composite temperature/humidity cyclic test.
NF C20-738*NF EN IEC 60068-2-38:2021 Environmental testing - Part 2-38 : tests - Test Z/AD : composite temperature/humidity cyclic test
NF X50-142:1990 SUPPLIER-USER RELATIONS. TESTS QUALITY. GUIDELINES FOR REQUESTING AND ORGANIZING TESTS.
NF U47-400:2014 Animal health analysis methods - Guide for the organisation of interlaboratory proficiency testing in animal health
NF C20-739:1999 Environmental testing. Part 2 : tests. Test Z/AMD : combined sequential cold, low air pressure and damp heat test.

Defense Logistics Agency

DLA MIL-DTL-5688 E (2)-2011 WIRE ROPE ASSEMBLIES; AIRCRAFT, PROOF TESTING AND PRESTRETCHING OF

German Institute for Standardization

DIN CEN/TS 764-8:2016-11*DIN SPEC 2930:2016-11 Pressure equipment and assemblies - Part 8: Proof test; German version CEN/TS 764-8:2016
DIN EN 60068-2-41:2000 Environmental testing - Part 2: Tests; test Z/BM: Combined dry heat/low air pressure tests (IEC 60068-2-41:1976 + A1:1983); German version EN 60068-2-41:1999
DIN 38402-45:2014 German standard methods for the examination of water, waste water and sludge - General information (group A) - Part 45: Interlaboratory comparisons for proficiency testing of laboratories (A 45)
DIN 38402-45:2003 German standard methods for the examination of water, waste water and sludge - General information (group A) - Part 45: Interlaboratory comparisons for proficiency testing of laboratories (A 45)
DIN EN 60068-2-39:2000 Environmental testing - Part 2: Tests; test Z/AMD: Combined sequential cold, low air pressure and damp heat test (IEC 60068-2-39:1976); German version EN 60068-2-39:1999
DIN 38402-42:2005 German standard methods for the examination of water, waste water and sludge - General informations (group A) - Part 42: Interlaboratory trials for method validation, evaluation (A 42)

Society of Automotive Engineers (SAE)

SAE AS5688-1998 Cable Assemblies, Aircraft, Proof Testing and Prestretching of
SAE AS2094-1995 Test Methods for Tube-Fitting Assemblies
SAE AS2094A-2011 Test Methods for Tube-Fitting Assemblies
SAE J1549-2015 Diesel Fuel Injection Pump - Validation of Calibrating Nozzle Holder Assemblies
SAE J2380-1998 Vibration Testing of Electric Vehicle Batteries
SAE AS36102-2005 Air Cargo Unit Load Devices - Testing Methods
SAE AS36102A-2012 Air Cargo unit Load Devices - Testing Methods

Canadian Standards Association (CSA)

CSA W178.1-02-2002 Certification of Welding Inspection Organizations Fourth Edition
CSA W178.1-08-2008 Certification of Welding Inspection Organizations Fifth Edition

U.S. Air Force

AIR FORCE A-A-59865-2010 INSULATION TEST SET

ITU-T - International Telecommunication Union/ITU Telcommunication Sector

SERIES G SUPP 44-2007 Test plan to verify B-PON interoperability (Study Group 15)
ITU-T X.1276-2018 Authentication step-up protocol and metadata Version 1.0 (Study Group 17)

RU-GOST R

GOST R ISO 14066-2013 Greenhouse gases. Competence requirements for greenhouse gas validation teams and verification team
GOST 24297-2013 Verification of purchased product. Organization and methods of control
GOST R 56979-2016 Photovoltaic modules. Ammonia corrosion testing
GOST R IEC 851-1-1994 Methods of test for winding wires. General
GOST 10243-1975 Steel. Methods of test and estimation of macrostructure
GOST R IEC 851-6-1994 Methods of test for winding wires. Thermal properties
GOST R IEC 851-3-1994 Methods of test for winding wires. Mechanical properties
GOST R IEC 851-4-1994 Methods of test for winding wires. Chemical properties
GOST R IEC 851-5-1994 Methods of test for winding wires. Electrical properties

Underwriters Laboratories (UL)

UL 10B-2020 Fire tests of door assemblies
UL 10B-1993 Fire tests of door assemblies
UL 10B-2008 UL Standard for Safety Fire Tests of Door Assemblies Tenth Edition
UL 580-2006 UL Standard for Safety Tests for Uplift Resistance of Roof Assemblies Fifth Edition
UL 580-2019 UL Standard for Safety Tests for Uplift Resistance of Roof Assemblies

International Electrotechnical Commission (IEC)

IEC TS 62915:2018 Photovoltaic (PV) modules - Type approval, design and safety qualification - Retesting
IEC 61345:1998 UV test for photovoltaic (PV) modules
IEC TS 63209-1:2021 Photovoltaic modules - Extended-stress testing - Part 1: Modules
IEC 61701:1995 Salt mist corrosion testing of photovoltaic (PV) modules
IEC 62759-1:2022 CMV Photovoltaic (PV) modules - Transportation testing - Part 1: Transportation and shipping of module package units
IEC 62759-1:2022 Photovoltaic (PV) modules - Transportation testing - Part 1: Transportation and shipping of module package units
IEC 61701:2011 Salt mist corrosion testing of photovoltaic (PV) modules
IEC TR 63279:2020 Derisking photovoltaic modules - Sequential and combined accelerated stress testing
IEC 61215-1:2021 RLV Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1: Test requirements
IEC 61215-2:2021 RLV Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
IEC 61701:2020 Photovoltaic (PV) modules - Salt mist corrosion testing
IEC 61215-1-1:2021 RLV Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-1: Special requirements for testing of crystalline silicon photovoltaic (PV) modules
IEC 62716:2013 Photovoltaic (PV) modules - Ammonia corrosion testing
IEC 60068-2-41:1976 Basic environmental testing procedures. Part 2 : Tests. Test Z/BM: Combined dry heat/low air pressure tests
IEC 60068-2-40:1976 Basic environmental testing procedures. Part 2 : Tests. Test Z/AM: Combined cold/low air pressure tests
IEC 62938:2020 Photovoltaic (PV) modules - Non-uniform snow load testing
IEC 60068-2-82:2019 Environmental testing - Part 2-82: Tests - Test Xw1: Whisker test methods for components and parts used in electronic assemblies
IEC 60068-2-41:1976/AMD1:1983 Basic environmental testing procedures. Part 2 : Tests. Test Z/BM: Combined dry heat/low air pressure tests

American National Standards Institute （ANSI)

ANSI/SCTE 45-2012 Test Method for Group Delay
ANSI/UL 10B-2009 Standard for Fire Tests of Door Assemblies
ANSI/UL 9-2004 Standard for Fire Tests of Window Assemblies
ANSI/ASME B18.18.2M-1987 Inspection and Quality Assurance For High-Volume Machine Assembly Fasteners
ANSI/ATIS 0600019-2009 Test Requirements for Pb-Free Subassembly Modules
ANSI/ATIS 0600020-2010 Test Requirements for Pb-free Circuit Packs
ANSI/UL 580-2009 Standard for Tests for Uplift Resistance of Roof Assemblies
ANSI/TIA/EIA 455-25C-2002 Repeated Impact Testing of Fiber Optic Cable Assemblies

British Standards Institution (BSI)

BS EN 12668-3:2000 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Combined equipment
BS EN 60851-1:1996+A2:2009 Winding wires - Test methods - General
BS EN 60851-1+A2:1998 Winding wires. Test methods. General
BS EN 60851-6:2012 Winding wires. Test methods. Thermal properties
BS EN 40-3-2:2013 Lighting columns. Design and verification. Verification by testing
BS EN 61189-5:2006 Test methods for electrical materials, interconnection structures and assemblies –– Part 5: Test methods for printed board assemblies
BS EN 61189-5:2009 Test methods for electrical materials, interconnection structures and assemblies - Test methods for printed board assemblies
BS EN 15888:2014 Transportable gas cylinders. Cylinder bundles. Periodic inspection and testing
BS EN 60851-5:2008 Winding wires – Test methods –– Part 5: Electrical properties
BS EN 60851-4:1998 Winding Wires - Test methods - Chemical properties
BS EN 60851-3:2009+A1:2013 Winding wires. Test methods. Mechanical properties
BS EN 60851-5:2008+A1:2011 Winding wires. Test methods. Electrical properties
BS EN 61701:2012 Salt mist corrosion testing of photovoltaic (PV) modules
BS EN 61189-6:2006 Test methods for electrical materials, interconnection structures and assemblies - Test methods for materials used in manufacturing electronic assemblies
BS EN 17038-2:2019 Pumps. Methods of qualification and verification of the Energy Efficiency Index for rotodynamic pump units - Testing and calculation of Energy Efficiency Index (EEI) of single pump units
BS EN 40-3-2:2000 Lighting columns - Design and verification - Verification by testing
BS EN ISO 20475:2020(2021) Gas cylinders — Cylinder bundles — Periodic inspection and testing
BS EN 50289-4-11:2002 Communication cables - Specifications for test methods - Environmental test methods - A horizontal integrated fire test method

Standard Association of Australia （SAA）

AS 60068.2.41:2003 Environmental testing - Tests - Test Z/BM: Combined dry heat/low air pressure tests
AS 60068.2.38:2003 Environmental testing - Tests - Test Z/AD: Composite temperature/humidity cyclic test
AS 2805.4.1:2001 Electronic funds transfer - Requirements for interfaces - Message authentication - Mechanisms using a block cipher
AS 60068.2.39:2003 Environmental testing - Tests - Test Z/AMD: Combined sequential cold, low air pressure and damp heat test
AS/NZS 1252.2:2016 High-strength steel fastener assemblies for structural engineering — Bolts, nuts and washers, Part 2: Verification testing for bolt assemblies
AS 60068.2.50:2003 Environmental testing - Tests - Test Z/Afc: Combined cold/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
AS 3439.1:1993 Low-voltage switchgear and controlgear assemblies Part 1: Type-tested and partially type-tested assemblies
AS 2582.16:2006 Complete, filled transport packages - Methods of test - Stability testing of unit loads
AS 60695.11.40:2006 Fire hazard testing - Test flames - Confirmatory tests - Guidance

Japanese Industrial Standards Committee (JISC)

JIS A 1529:1997 Doorsets -- Static loading test
JIS C 0031:1995 Environmental testing Part 2: Tests, Test Z/BM: Combined dry heat/low air pressure tests
JIS C 60068-2-40:1995 Environmental testing Part 2: Tests, Test Z/AM: Combined cold/low air pressure tests
JIS B 8623:1986 Testing methods for refrigerant condensing units
JIS A 1523:1996 Doorsets -- Static torsion test
JIS C 60068-2-41:1995 Environmental testing Part 2: Tests, Test Z/BM: Combined dry heat/low air pressure tests
JIS Z 0170:1998 Unit loads -- Stability testing
JIS C 0030:1995 Environmental testing Part 2: Tests, Test Z/AM: Combined cold/low air pressure tests
JIS H 8664:2004 Test methods for build-up thermal spraying
JIS A 1525:1996 Doorsets -- Repeated opening and closing test
JIS A 4710:1996 Windows and doorsets -- Thermal resistance test
JIS A 1515:1998 Windows and doorsets -- Wind resistance test
JIS A 1524:1996 Doorsets -- Vertical load test
JIS A 1516:1998 Windows and doorsets -- Air permeability test
JIS A 1518:1996 Doorsets -- Soft heavy body impact test
JIS C 60068-2-39:2004 Environmental testing -- Part 2: Tests. Test Z/AMD: Combined sequential cold, low air pressure, and damp heat test
JIS B 7726:1997 Rockwell hardness test -- Verification of testing machines
JIS B 7725:2010 Vickers hardness test -- Verification and calibration of testing machines
JIS C 0028:1988 Basic environmental testing procedures Part 2: Tests Test Z/AD: Composite temperature/humidity cyclic test
JIS C 5106:1977 Testing methods for ceramic based multiple components
JIS B 8623:2002 Testing methods of refrigerant condensing units
JIS B 7726:2010 Rockwell hardness test -- Verification and calibration of testing machines
JIS B 7734:1997 Knoop hardness test -- Verification of testing machines
JIS B 7725:1997 Vickers hardness test -- Verification of testing machines

PL-PKN

PN E04164-06-1988 Enamelled winding round wires Methods of test Cut-through test
PN E04164-03-1986 Enamelled winding round wires Methods of testing Test for resistance to abrasion
PN E04160-32-1987 Electric cables Methods of testing Hot set test
PN E04164-00-1988 Enamelled winding round wires Methods of test General
PN-EN 1488-2021-10 E Building valves -- Expansion groups -- Tests and requirements
PN E04164-09-1986 Enamelled winding round wires Methods of testing Solder test
PN-EN 17418-2021-08 E Two-component epoxy and polyurethane adhesives for on-site repair of cracked timber structures--Testing, requirements and repair strength verification
PN B06714-11-1987 Mineral aggrcgates Testings Determination of petrography composition
PN E04164-12-1988 Enamelled round winding wires Methods of test Test of the electrical properties
PN E04164-02-1986 Enamelled winding round wires Methods of testing Test of the mechanical characteristics of enamelled wires

American Society for Testing and Materials (ASTM)

ASTM E1597-10(2015) Standard Test Method for Saltwater Pressure Immersion and Temperature Testing of Photovoltaic Modules for Marine Environments
ASTM E2010-99 Standard Test Method for Positive Pressure Fire Tests of Window Assemblies
ASTM E2481-12(2018) Standard Test Method for Hot Spot Protection Testing of Photovoltaic Modules
ASTM E2481-12(2023) Standard Test Method for Hot Spot Protection Testing of Photovoltaic Modules
ASTM E73-83(2007) Standard Practice for Static Load Testing of Truss Assemblies
ASTM E2189-02 Standard Test Method for Testing Resistance to Fogging in Insulating Glass Units
ASTM E2189-19 Standard Test Method for Testing Resistance to Fogging in Insulating Glass Units
ASTM E2074-00 Standard Test Method for Fire Tests of Door Assemblies, Including Positive Pressure Testing of Side-Hinged and Pivoted Swinging Door Assemblies
ASTM F1639-95 Standard Test Method for Performance of Combination Ovens
ASTM E73-83(1996)e1 Standard Practice for Static Load Testing of Truss Assemblies
ASTM E163-80 Standard Methods of Fire Tests Of Window Assemblies
ASTM F1639-95(2001) Standard Test Method for Performance of Combination Ovens
ASTM D5506-98 Standard Practice for Organizations Engaged in the Certification of Personnel Testing and Inspecting Bituminous Paving Materials
ASTM E2010-01 Standard Test Method for Positive Pressure Fire Tests of Window Assemblies (Withdrawn 2007)
ASTM D5506-08 Standard Practice for Organizations Engaged in the Certification of Personnel Testing and Inspecting Bituminous Paving Materials
ASTM D5506-98(2003) Standard Practice for Organizations Engaged in the Certification of Personnel Testing and Inspecting Bituminous Paving Materials

GSO

GSO ISO 11170:2015 Hydraulic fluid power -- Sequence of tests for verifying performance characteristics of filter elements
GSO ISO 10961:2015 Gas cylinders -- Cylinder bundles -- Design, manufacture, testing and inspection
OS GSO ISO 10961:2015 Gas cylinders -- Cylinder bundles -- Design, manufacture, testing and inspection
GSO ISO/TR 8865:2013 Mining -- Guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
GSO ISO 8270:2007 Doorsets - Soft heavy body impact test
BH GSO ISO 10961:2016 Gas cylinders -- Cylinder bundles -- Design, manufacture, testing and inspection
OS GSO IEC 60575:1997 Thermal - mechanical performance test and mechanical performance test on string insulator units.
OS GSO 1519:2002 Low - voltage switchgear and controlgear assemblies Part 1 : Type - tested and partially type - tested assemblies
BH GSO ISO/TR 8865:2016 Mining -- Guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
GSO ISO 20475:2022 Gas cylinders — Cylinder bundles — Periodic inspection and testing
GSO ISO 8332:2015 Rubber compounding ingredients -- Sulfur -- Methods of test
BH GSO ISO 20475:2023 Gas cylinders — Cylinder bundles — Periodic inspection and testing

(U.S.) Ford Automotive Standards

FORD FLTM BA 120-01-2021 RESISTANCE SPOT WELDING ACCEPTANCE TEST FOR HETEROGENEOUS STEEL COMBINATIONS

Danish Standards Foundation

DS/EN ISO 10961:2012 Gas cylinders - Cylinder bundles - Design, manufacture, testing and inspection
DS 1051.2:1980 Fire-resistance tests. Door and shutter assemblies
DS/EN 61189-5:2007 Test methods for electrical materials, interconnection structures and assemblies - Part 5: Test methods for printed board assemblies

KR-KS

KS B 4227-2008(2023) Performance test method of modular jig and fixture
KS E ISO 8865-2022 Mining — Guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
KS B 6359-2008(2023) Testing method for mechanical transport refrigeration units
KS C IEC 60068-2-82-2021 Environmental testing — Part 2-82: Tests — Test Xw1: Whisker test methods for components and parts used in electronic assemblies

International Organization for Standardization (ISO)

ISO 3008:1976 Fire-resistance tests; Door and shutter assemblies
ISO 16964:2015 Gas cylinders — Flexible hoses assemblies — Specification and testing
ISO 12097-2:1996 Road vehicles - Airbag components - Part 2: Testing of airbag modules
ISO/R 205:1961 Determination of proof stress and proving test for steel at elevated temperature
ISO/TR 8865:1990 Mining; guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors
ISO 9815:1992 Passenger car/trailer combinations; lateral stability test
ISO 11339:1993 Adhesives; 180° peel test for flexible-to-flexible bonded assemblies (T-peel test)

GM Holden Ltd

HOLDEN HN 0027-1989 Environmental Testing of Components and Assemblies

TR-TSE

TS 3439-1979 TEST CODE FOR ACCEPTANCE OF STEAM TURBINES
TS 286-1965 VERIFICATION OF MATERIALS TESTING MACHINES

VN-TCVN

TCVN 7699-2-38-2007 Environmental testing.Part 2-38: Tests.Test Z/AD: Composite temperature/humidity cyclic test
TCVN 7699-2-39-2007 Environmental testing.Part 2-39: Tests.Test Z/AMD: Combined sequential cold, low air pressure and damp heat test

ES-AENOR

UNE 20-501 Pt.2-40-1986 Electronic device machine components. Basic tests of climatic and mechanical soundness. Z/AM test: cold and low pressure environment combined test

European Committee for Electrotechnical Standardization（CENELEC）

HD 323.2.40 S1-1988 Basic Environmental Testing Procedures - Part 2: Tests Test Z/AM: Combined Cold/Low Air Pressure Tests
EN 61189-5:2006 Test methods for electrical materials, interconnection structures and assemblies - Part 5: Test methods for printed board assemblies
EN 61345:1998 UV Test for Photovoltaic (PV) Modules

American Society of Mechanical Engineers (ASME)

ASME B18.18.2-2009 Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners
ASME B18.18.2M-1987 Inspection and Quality Assurance for High-Volume Machine Assembly Fasteners

ATIS - Alliance for Telecommunications Industry Solutions

0300230-2015 Telecommunications Charge Card and Billed Number Screening Validation Message Components
T1.230-1994 Telecommunications - Telecommunications Charge Card and Billed Number Screening Validation Message Components
0300230-2010 Telecommunications Charge Card and Billed Number Screening Validation Message Components (Pre-Pub)

SE-SIS

SIS SS 02 71 06-1990 Geotechnical tests — Mineral soils — Grain size fractions

Alliance of Telecommunications Industry Solutions （ATIS)

ATIS 0300230-2015 Telecommunications Charge Card and Billed Number Screening Validation Message Components
ATIS 0300230-2010 Telecommunications Charge Card and Billed Number Screening Validation Message Components

TH-TISI

TIS 1335-1996 Ftre.resistance tests.door and shutter assemblies

United States Navy

NAVY MIL-T-85284 NOTICE 1-1998 TEST SET, ADAPTER GROUP, OF-65/ASM
NAVY MIL-T-85284-1983 TEST SET, ADAPTER GROUP, OF-65/ASM
NAVY MIL-T-85472 A-1987 TEST SET, GROUP OQ-169B/DSM-96A, SPECIFICATION FOR

Lithuanian Standards Office

LST EN 12668-3-2014 Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment

IPC - Association Connecting Electronics Industries

IPC 8701-2014 Final Acceptance Criteria Standard for PV Modules-Final Module Assembly
IPC 9262-2016 Specification for Characterization and Verification of Assembly Level Automatic Optical Inspection Equipment

International Telecommunication Union (ITU)

ITU-T SERIES G SUPP 44-2007 Test plan to verify B-PON interoperability Study Group 15

IETF - Internet Engineering Task Force

RFC 7628-2015 A Set of Simple Authentication and Security Layer (SASL) Mechanisms for OAuth

Malaysia Standards

MS 1445 Pt.1-1998 Low-voltage switchgear and controlgear components: Part 1: Type-tested and partially type-tested components

GOST

GOST R 59777-2021 Photovoltaic modules. Non-uniform snow load testing

Indonesia Standards

SNI IEC 60439-1:2009 Low-voltage switchgear and controlgear assemblies. Part 1: Type-tested and partially type-tested assemblies

IN-BIS

IS 3613-1974 Acceptance test of wire-flux combination for submerged arc welding of structural steel

American Welding Society (AWS)

AWS WI CH 14-2000 Proof Tests(Welding Inspection)

Others: Internal Validation Validation Groups and Groups,internal verification group,Test group Verification group,verification group,Within-group and between-group tests